Fe3O4/Graphene Composite Anode Material for Fast-Charging Li-Ion Batteries.

Composite anode material based on Fe3O4 and reduced graphene oxide is prepared by base-catalysed co-precipitation and sonochemical dispersion. Structural and morphological characterizations demonstrate an effective and homogeneous embedding of Fe3O4 nanoparticles in the carbonaceous matrix. Electrochemical characterization highlights specific capacities higher than 1000 mAh g-1 at 1C, while a capacity of 980 mAhg-1 is retained at 4C, with outstanding cycling stability. These results demonstrate a synergistic effect by nanosize morphology of Fe3O4 and inter-particle conductivity of graphene nanosheets, which also contribute to enhancing the mechanical and cycling stability of the electrode. The outstanding capacity delivered at high rates suggests a possible application of the anode material for high-power systems.

Novel MIPs-Parabens based SPE Stationary Phases Characterization and Application.

In this work, the synthesis, characterization, and application of novel parabens imprinted polymers as highly selective solid-phase extraction (SPE) sorbents have been reported. The imprinted polymers were created using sol-gel molecular imprinting process. All the seven parabens were considered herein in order to check the phase selectivity. By means of a validated HPLC-photodiode array detector (PDA) method all seven parabens were resolved in a single chromatographic run of 25 min. These SPE sorbents, in-house packed in SPE empty cartridges, were first characterized in terms of extraction capability, breakthrough volume, retention volume, hold-up volume, number of theoretical plates, and retention factor. Finally, the device was applied to a real urine sample to check the method feasibility on a very complex matrix. The new paraben imprinted SPE sorbents, not yet present in the literature, potentially encourage the development of novel molecularly imprinted polymers (MIPs) to enhance the extraction efficiency, and consequently the overall analytical performances, when the trace quantification is required.

Electrospun Carbon/Cu x O Nanocomposite material as Sustainable and High Performance Anode for Lithium-Ion Batteries.

The increase in energy density of the next generation of battery materials to meet the new challenges of the electrical vehicles era calls for innovative and easily scalable materials with sustainable processes. An innovative Cu x O/C nanocomposite material, characterized by a highly conductive 3D-framework, with Cu x O/Cu-metal contiguous nanodomains is prepared by electrospinning. The electrode processing is made using a polyacrylic acid binder. The nanocomposite has been fully characterized and the electrochemical performance shows high specific capacity values over 450 galvanostatic cycles at 500 mAg-1 specific current with capacity retention values over 80 %. In addition, the composite shows remarkable high rate performance and highly stable interface, which has been studied by impedance spectroscopy.

Tin-Decorated Reduced Graphene Oxide and NaLi0.2Ni0.25Mn0.75O as Electrode Materials for Sodium-Ion Batteries.

A tin-decorated reduced graphene oxide, originally developed for lithium-ion batteries, has been investigated as an anode in sodium-ion batteries. The composite has been synthetized through microwave reduction of poly acrylic acid functionalized graphene oxide and a tin oxide organic precursor. The final product morphology reveals a composite in which Sn and SnO2 nanoparticles are homogenously distributed into the reduced graphene oxide matrix. The XRD confirms the initial simultaneous presence of Sn and SnO2 particles. SnRGO electrodes, prepared using Super-P carbon as conducting additive and Pattex PL50 as aqueous binder, were investigated in a sodium metal cell. The Sn-RGO showed a high irreversible first cycle capacity: only 52% of the first cycle discharge capacity was recovered in the following charge cycle. After three cycles, a stable SEI layer was developed and the cell began to work reversibly: the practical reversible capability of the material was 170 mA·h·g-1. Subsequently, a material of formula NaLi0.2Ni0.25Mn0.75O was synthesized by solid-state chemistry. It was found that the cathode showed a high degree of crystallization with hexagonal P2-structure, space group P63/mmc. The material was electrochemically characterized in sodium cell: the discharge-specific capacity increased with cycling, reaching at the end of the fifth cycle a capacity of 82 mA·h·g-1. After testing as a secondary cathode in a sodium metal cell, NaLi0.2Ni0.25Mn0.75O was coupled with SnRGO anode to form a sodium-ion cell. The electrochemical characterization allowed confirmation that the battery was able to reversibly cycle sodium ions. The cell's power response was evaluated by discharging the SIB at different rates. At the lower discharge rate, the anode capacity approached the rated value (170 mA·h·g-1). By increasing the discharge current, the capacity decreased but the decline was not so pronounced: the anode discharged about 80% of the rated capacity at 1 C rate and more than 50% at 5 C rate.

Comparison between Exhaustive and Equilibrium Extraction Using Different SPE Sorbents and Sol-Gel Carbowax 20M Coated FPSE Media.

This paper reports the performance comparison between the exhaustive and equilibrium extraction using classical Avantor C18 solid phase extraction (SPE) sorbent, hydrophilic-lipophilic balance (HLB) SPE sorbent, Sep-Pak C18 SPE sorbent, novel sol-gel Carbowax 20M (sol-gel CW 20M) SPE sorbent, and sol-gel CW 20M coated fabric phase sorptive extraction (FPSE) media for the simultaneous extraction and analysis of three inflammatory bowel disease (IBD) drugs that possess logP values (polarity) ranging from 1.66 for cortisone, 2.30 for ciprofloxacin, and 2.92 for sulfasalazine. Both the commercial SPE phases and in-house synthesized sol-gel CW 20M SPE phases were loaded in SPE cartridges and the extractions were carried out under an exhaustive extraction mode. FPSE was carried out under an equilibrium extraction mode. The drug compounds were resolved using a Luna C18 column (250 mm × 4.6 mm; 5 m particle size) in gradient elution mode within 20 min and the method was validated in compliance with international guidelines for the bioanalytical method validation. Novel in-house synthesized and loaded sol-gel CW 20M SPE sorbent cartridges were characterized in terms of their extraction capability, breakthrough volume, retention volume, hold-up volume, number of the theoretical plate, and the retention factor.

Anatase TiO2 as a Cheap and Sustainable Buffering Filler for Silicon Nanoparticles in Lithium-Ion Battery Anodes.

The design of effective supporting matrices to efficiently cycle Si nanoparticles is often difficult to achieve and requires complex preparation strategies. In this work, we present a simple synthesis of low-cost and environmentally benign aAnatase TiO2 nanoparticles as buffering filler for Si nanoparticles (Si@TiO2 ). The average anatase TiO2 crystallite size was approximately 5 nm. A complete structural, morphological, and electrochemical characterization was performed. Electrochemical test results show very good specific capacity values of up to 1000 mAh g-1 and cycling at several specific currents, ranging from 500 to 2000 mA g-1 , demonstrating a very good tolerance to high cycling rates. Postmortem morphological analysis shows very good electrode integrity after 100 cycles at 500 mA g-1 specific current.